Panel yapılandırması 17MB130S ve VES650QNTL-2D-U1 gerektirir

DoubleM257 · Çarşamba saat 14:33'de

Merhaba Google Translate ile yazıyorum.
Vestel 17MB130S ve VES650QNTL-2D-U11 panelli bir "ODL 65650U-TIB" sahibiyim. Televizyonun seri numarası: 8112360800258. Aynı tip 17MB130S yeni anakart taktım ve yazılımı USB stick ile yükledim. TV açılıyor ama ne yazık ki görüntü tamamen yanlış. Panel konfigürasyonuna ihtiyacım olduğunu düşünüyorum. Birisi bana bu dosyaları gönderebilir mi lütfen?

yokoono · Çarşamba saat 15:13'de

Save the panel profile from TV and post it here.
It is saved with the folder downloadpq.mb130

DoubleM257 · Çarşamba saat 15:20'de

yokoono' Alıntı:
Save the panel profile from TV and post it here.
It is saved with the folder downloadpq.mb130

Ziyaretçiler için gizlenmiş link,görmek için Giriş yap veya üye ol.

yokoono · Çarşamba saat 15:32'de

Try. With folder pq.

Ziyaretçiler için gizlenmiş link,görmek için Giriş yap veya üye ol.

1. Format a stick with FAT32
2. Create a folder called pq on the stick
3. Unzip and put the 2 files in the folder
4. Turn on the TV, USB stick and type MENU 4725
5. Go to USB Operations and type OK on the remote control
6. Wait 10 seconds and exit the menu (return, back)
7. Turn off the TV from the remote control
8. Wait until the stby LED on the TV stops flashing
9. Unplug the TV and wait until the stby light goes out.
10. Take out the stick and turn on the TV.
If the image is not correct, repeat the operation

DoubleM257 · Çarşamba saat 15:46'de

yokoono' Alıntı:
Try. With folder pq.

Ziyaretçiler için gizlenmiş link,görmek için Giriş yap veya üye ol.

I Installed your pq files, but the picture is now more bad. Here are pictures. The red LED is flashing continuously.

yokoono · Çarşamba saat 15:48'de

Read the installation procedure.

7. Turn off the TV from the remote control
8. Wait until the stby LED on the TV stops flashing
9. Unplug the TV and wait until the stby light goes out.
10. Take out the stick and turn on the TV.
If the image is not correct, repeat the operation

DoubleM257 · Çarşamba saat 15:56'de

yokoono' Alıntı:
Read the installation procedure.

I read the installation instructions several times and repeated the process 3 times. Unfortunately the picture remains just as bad. I noticed that in the service menu on the right side many entries now say "File Not Found"; previously there were file names there. Thanks for your help

yokoono · Çarşamba saat 15:59'de

Full software. But is for Finlux. Try at you risk

Ziyaretçiler için gizlenmiş link,görmek için Giriş yap veya üye ol.

DoubleM257 · Çarşamba saat 16:25'de

yokoono' Alıntı:
Full software. But is for Finlux. Try at you risk

Ziyaretçiler için gizlenmiş link,görmek için Giriş yap veya üye ol.

Thank you for your help, but this software does not solve my problem. The picture of the TV is still bad. I bought a other 17MB130S. Can I connect it and do a software update or should I solder the SPI IC out and reprogram it ?

yokoono · Çarşamba saat 16:28'de

Change the motherboard and turn on the TV. Then see what happens.

DoubleM257 · Çarşamba saat 16:55'de

I have exactly the same problem with the new motherboard. I think the TV can no longer be saved...

yokoono · Çarşamba saat 16:59'de

Post service menu (menu 4725).

DoubleM257 · Çarşamba saat 17:04'de

yokoono' Alıntı:
Post service menu (menu 4725).

That's now with the new motherboard from a Toshiba 55 inch

yokoono · Çarşamba saat 17:16'de

And this main was rewritten with the wrong software. It should have been written in the menu VES550xxxx-xx-xx. Save the panel profile and send it.